Installing A Bath tub
Installing A Bath tub
Blog Article
Presented here in the next paragraph you will find lots of really good facts in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't exactly rocket science, yet it does need strong plumbing, carpentry, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately tough job. If the old tub is easily obtainable, the job can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and also position the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the task and also are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed job, it is far better to consider employing one prior to you start. Chances are you might need an expert plumber to make tube links.
This write-up will assist you mount a new bathtub in your shower room if you have actually already gotten a brand-new bathtub and don't need to transform the setup of your previous water supply pipes.
Your tools as well as product checklist should comprise the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the limited access that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the supply of water as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washers are in location in between the faucet as well as the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a stiff seal, causing the water to penetrate the wall between the bath as well as the tiling, causing problems with dampness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components and also fittings. They are sold in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack rather early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very intrigued by How to Install a Bathtub Yourself and I am assuming you enjoyed reading the blog post. Please take the opportunity to promote this content if you liked it. Thanks a lot for going through it.
Schedule Here
Report this page